CHF75.90
Stock: 4
Available, delivery time 1-3 days
Maxi Fogger and humidifier
The compact Fogger & humidifier Maxi is ideal for pets that require a humid environment. Adjustable fogging output (up to 250 ml per hour). Flexible adjustable hose from 45 cm to 150 cm length. Dry run protection, switches off the unit when the tank is empty. Compatible with a wide range of enclosures including vivariums, tanks, cages, terrariums, aquariums, plastic/PVC/acrylic/glass containers.
Perfect for a variety of reptiles and amphibians including bearded dragons, geckos, snakes, turtles, iguanas, lizards, chameleons, frogs, crabs, etc.
Description of the Fogger & Humidifier
Remove all packaging. Place the humidifier base (A) in an accessible place next to your terrarium or inside the area.
Before use, unscrew the valve on the black base of the humidifier container (B) and rinse the container with a small amount of soap. Rinse it well until no more soapy water comes out when rinsing.
Fill the humidifier container (B) with up to 2 litres of water. Tighten the valve again.
Place the humidifier tank (B) on the base (A). Check carefully that the humidifier tank is installed correctly on the base.
Plug the larger end of the extendable hose (C) onto the black neck of the humidifier tank.
Extend the hose (C) and place the end in/on the top or side of the terrarium. Slide the suction cups down the hose and stick them to the side of the terrarium.
Connect the unit. Turn on the switch on the back of the humidifier base (A). Set the control on the front of the unit to the desired output. It may take a few seconds for the output to increase/decrease after adjusting the control.
In a fogger and humidifier is:
- Main unit
- Extension hose
- Connector
- Tank cap
- Suction cups
- Water tank
Technical data:
- Maximum power: 32W
- Voltage: 220V
- Frequency: 50Hz
- Maximum capacity: 2,2l
- Maximum output 250ml/h
Installing the Fogger and Humidifier Maxi
Place the humidifier horizontally in a suitable place, remove the water tank, unscrew the lid of the water tank and fill it with water. The water temperature must not exceed 40 °C. After filling the water tank completely, remove the water drops and then reattach it to the main unit.
Attach the tank cap to the upper part of the water tank. Connect the connector to the water tank lid.Connect the flexible hose to the connector.Attach the suction cups on the glass to flexible hose and adjust the appropriate length of flexible hose.
Attach the suction cups to the side or back of the terrarium and point the outlet of the flexible tube towards the inside of the terrarium. Bend the extension tube as little as possible. Damage to the extension tube may result in faulty fogging.
Connect the unit to the mains (220/50 Hz) and set the switch on the main unit to the "On" position.
Turn the fog output adjustment knob and adjust the fog output according to your needs.
The unit is equipped with a low-water cut-out. When the water tank is empty, the sensor switches off the fan and the transformer. As a result, no mist comes out of the flexible hose and the indicator light lights up red. If you want to continue operation, switch off the power and fill the tank with water again.
Caution: Do not pour hot water above 40 °C into the water tank to avoid deforming the motor unit. Do not pour water directly into the water tank when the tank is installed on the main unit. Do not pour metal products, chemicals and detergents into the tank.
Remove the water from the tank when the ambient temperature is below 0 °C. This could cause frost, which could damage the unit.
Do not move the unit while it is in operation. If the appliance is not used for a long time, switch it off and disconnect it from the mains supply
1 of 1 reviews
4 out of 5 stars
Login
April 8, 2023 10:17
Sehr effektiv.
Sehr effektiv.
Fogger Zubehör
Suggested products
Customers also bought
Customers also viewed